In this paper, the effect of electric boundary conditions on Mode I crack propagation in ferroelectric ceramics is studied by using both linear and nonlinear piezoelectric fracture mechanics. In linear analysis, impermeable cracks under open circuit and short circuit are analyzed using the Stroh formalism and a rescaling method. It is shown that the energy release rate in short circuit is larger than that in open circuit. In nonlinear analysis, permeable crack conditions are used and the nonlinear effect of domain switching near a crack tip is considered using an energy-based switching criterion proposed by Hwang et al.（Acta Metal. Mater.,1995）. In open circuit, a large depolarization field induced by domain switching makes switching much more diffcult than that in short circuit. Analysis shows that the energy release rate in short circuit is still larger than that in open circuit, and is also larger than the linear result. Consequently,whether using linear or nonlinear fracture analysis, a crack is found easier to propagate in short circuit than in open circuit, which is consistent with the experimental observations of Kounga Njiwa et al.（Eng. Fract. Mech., 2006）.
Piezoelectric bar-shaped resonators were proposed to act as hardness sensors in the 1960 s and stiffness sensors in the 1990 s based on the contact impedance method.In this work, we point out that both multilayer and unimorph（or bimorph） piezoelectric actuators could act as stiffness/modulus sensors based on the principle of mechanical contact resonance. First, the practical design and the performance of a piezoelectric unimorph actuator–based stiffness sensor were presented. Then the working principle of piezoelectric multilayer actuator–based stiffness sensors was given and verified by numerical investigation. It was found that for these two types of resonance-based sensors, the shift of the resonance frequency due to contact is always positive, which is different from that of the contact impedance method. Further comparative sensitivity study indicated that the unimorph actuator–based stiffness sensor is very suitable for measurement on soft materials, whereas the multilayer actuator–based sensor is more suitable for hard materials.
This paper studies the dynamic conducting crack propagation in piezoelectric solids under suddenly in-plane shear loading. Based on the integral transform methods and the Wiener-Hopf technique, the resulting mixed boundary value problem is solved. The analytical solutions of the dynamic stress intensity factor and dynamic electric displacement intensity factor for the Mode II case are derived. Furthermore, the numerical results are presented to illustrate the characteristics of the dynamic crack propagation. It is shown that the universal functions for the dynamic stress and electric displacement intensity factors vanish if the crack propagation speed equals the generalized Rayleigh speed. The results indicate that the defined electro-mechanical coupling coefficient is of great importance to the universal functions and stress intensity factor history.
The stress-induced magnetic domain switching in FeGa thin films is studied using phase-field method. In particular, the magnetic field is applied along the [110] direction and biaxial stresses are applied along [ 100] and [010]. A compressive pre-stress corresponds to a smaller coercive magnetic field while a tensile pre-stress corresponded to a larger coercive field. At the same time, it is also found that the transition between butterfly and square-like magnetostriction loops occurs at the critical opposite biaxial stress state. The two different evolutions correspond to two different mechanisms： one is that the single domain swings across a fan area back and forth; the other is that the single domain turns a clockwise circle. The results can be explained bv the stress tuned anisotronv energy well.
As rapid development in wearable/implantable electronic devices benefit human life in daily health monitoring and disease treatment medically, all kinds of flexible and/or stretchable electronic devices are booming, together with which is the demanding of energy supply with similar mechanical property. Due to its ability in converting mechanical energy lying in human body into electric energy, energy harvesters based on piezoelectric materials are promising for applications in wearable/implantable device's energy supply in a renewable, clean and life-long way. Here the mechanics of traditional piezoelectrics in energy harvesting is reviewed, including why piezoelectricity is the choice for minor energy harvesting to power the implantable/wearable electronics and how. Different kinds of up to date flexible piezoelectric devices for energy harvesting are introduced, such as nanogenerators based on Zn O and thin and conformal energy harvester based on PZT. A detailed theoretical model of the flexible thin film energy harvester based on PZT nanoribbons is summarized, together with the in vivo demonstration of energy harvesting by integrating it with swine heart. Then the initial researches on stretchable energy harvesters based on piezoelectric material in wavy or serpentine configuration are introduced as well.
A magnetoelectric(ME) laminated composite made of one pair of piezoelectric Pb(Zr,Ti)O3(PZT) fiber layers with multiple push–pull polarization units laminated between high-permeability metglas ribbon layers with a differential configuration was proposed for vibration noise suppression. Unlike conventional metglas/PZT fiber/metglas three-layer ME laminated structures, the differential configuration has the capability to reject vibration-induced noise from the magnetic signal. The experiment results showed that the differential ME laminated composite was with up to 30 times enhancement in signal-to-noise ratio.
In recent years,industries in the fields of petrochemical,automotive,and aerospace have expressed their interest in utilizing piezoelectric actuators for high-temperature(HT)operations at the temperature above 150℃.HT piezoelectric ceramics(1x)BiScO_(3-x)PbTiO_(3)(BS-PT)are considered as one of the most competitive piezoelectric actuation materials used in the harsh environment because of its high Curie temperature(T_(C)=450℃)as well as high piezoelectric coefficient(d_(33)=460 pC/N)in the MPB composition.This paper summarized the recent progress in HT piezoelectric ceramics and actuators based on BS-PT solid solutions.The properties of BS-PT piezoelectric ceramics and actuators,including driving mechanisms,actuation performances and their applications in HT environment were also discussed.
